Hybrid journal (It can contain Open Access articles) ISSN (Print) 2043-8648 - ISSN (Online) 2043-8656 Published by Inderscience Publishers[449 journals]

Authors:Hong-Ping Zhu, Ling Ye, Shun Weng Pages: 213 - 232 Abstract: Dynamic analysis of the vehicle-track coupling system is important to the structural design, damage detection and condition assessment. In this paper, the uncertain system parameters are modelled as fuzzy variables instead of deterministic values or conventional random variables with known probability distributions. Afterwards, the dynamic response functions of the coupling system are transformed into a component function based on the high dimensional representation approximation. Then, the Lagrange interpolation method is used to approximate the component function. Finally, the bounds of the dynamic responses can be predicted by performing Monte Carlo method on the interpolation polynomials of Lagrange interpolation function, avoiding the expensive Monte Carlo process on the subway vehicle-track coupling system. A numerical example is analysed by the proposed method to predict the bounds of the subway vehicle-track coupling system responses. The results show that the proposed method is effective and efficient to predict the bounds of the system responses. Keywords: subway vehicle-track coupling system; fuzzy variables; high dimensional representation approach; Monte Carlo simulation Citation: International Journal of Lifecycle Performance Engineering, Vol. 3, No. 3/4 (2019) pp. 213 - 232 PubDate: 2019-11-22T23:20:50-05:00 DOI: 10.1504/IJLCPE.2019.103690 Issue No:Vol. 3, No. 3/4 (2019)

Authors:Haoqi Wang, Tomonori Nagayama Pages: 233 - 256 Abstract: For the identification of bridge parameters such as modal mass, both the excitation on a bridge and its corresponding bridge responses must be measured simultaneously. Vehicle-induced load can be used for bridge parameter identification if vehicle-bridge contact force is well estimated. Herein, a two-step algorithm is proposed to identify bridge modal mass. The first step is to estimate the vehicle tyre forces from measured vehicle responses. In the second step, the estimated tyre forces and the simultaneously measured vehicle-induced bridge acceleration responses are used as the input and output of the bridge system, respectively, to identify the bridge modal mass. Numerical examples clarify the modal mass identification performance considering observation noises and differences in the left and right path profiles. Field measurement was conducted, and the results indicate that the proposed algorithm can identify the first modal mass with satisfactory accuracy. Keywords: bridge assessment; drive-by monitoring; tyre force estimation; bridge modal mass; augmented Kalman filter; AKF Citation: International Journal of Lifecycle Performance Engineering, Vol. 3, No. 3/4 (2019) pp. 233 - 256 PubDate: 2019-11-22T23:20:50-05:00 DOI: 10.1504/IJLCPE.2019.103692 Issue No:Vol. 3, No. 3/4 (2019)

Authors:Yun Zhou, Sai Zhou, Lu Deng, Songbai Chen, Weijian Yi Pages: 257 - 288 Abstract: Moving load identification from the dynamic responses of bridges is a typical inverse problem that is solved to estimate vehicle axle loads in motion from observed data. To reduce the ill-posedness of the problem and improve solution accuracy, this paper proposes a method for reconstructing the dynamic displacement response via combining the measured acceleration and strain signals for moving load identification. The identification accuracy achieved by employing the reconstructed displacement under different vehicle speeds and different identification algorithms was investigated via finite element (FE) analysis, and a laboratory experiment of a simply supported beam model was constructed to validate the effectiveness of the proposed method. Both the computation simulations and experimental results indicate that the reconstructed displacements fit the true values well and the proposed method can effectively overcome the ill-posedness of the problem in terms of equation resolution and achieve a high level of accuracy. Keywords: moving load identification; acceleration; dynamic strain; signal reconstruction; modal decomposition Citation: International Journal of Lifecycle Performance Engineering, Vol. 3, No. 3/4 (2019) pp. 257 - 288 PubDate: 2019-11-22T23:20:50-05:00 DOI: 10.1504/IJLCPE.2019.103696 Issue No:Vol. 3, No. 3/4 (2019)

Authors:Kai-Chun Chang, Chul-Woo Kim, Souichiro Hasegawa, Shunsuke Nakajima, Patrick J. McGetrick Pages: 289 - 309 Abstract: Accurate estimation of road surface profiles is an important issue for inspection and maintenance of roadway bridges. Recently, a simple method was proposed to complete this task, using a limited number of accelerometers installed on a non-specialised vehicle to estimate road surface profiles from the vehicle's acceleration responses. Its feasibility was preliminarily tested by several numerical simulations and laboratory experiments but validation via field experiments has yet to be completed. This paper presents the investigation of the feasibility of this method for implementation in practice; to this end, a field experiment was conducted on a 40.5 m long simply-supported composite-girder bridge. A compact SUV was employed as the test vehicle. In the field experiment, the road surface profile was estimated with acceptable accuracy using this method, with most peaks and troughs identified. In particular, an artificial hump installed on the bridge was clearly identified, implying that the investigated method was able to detect an abrupt change in the road surface profile, which could be caused by damage. Parametric studies were carried out showing that the vehicle speed had little effect on the estimation accuracy while a heavier vehicle presented better estimation accuracy. Keywords: road surface profile; drive-by method; field test; pavement maintenance; moving force identification; inverse problem; vehicle dynamics Citation: International Journal of Lifecycle Performance Engineering, Vol. 3, No. 3/4 (2019) pp. 289 - 309 PubDate: 2019-11-22T23:20:50-05:00 DOI: 10.1504/IJLCPE.2019.103698 Issue No:Vol. 3, No. 3/4 (2019)

Authors:Yuta Takahashi, Kyosuke Yamamoto Pages: 310 - 330 Abstract: Screening method can be an option for maintaining large number of bridges. However, there is a need to evaluate each bridge at a low cost and high efficiency. This study applies data processing to the vibration data of the vehicle in order to improve efficiency. For example, spatial singular mode angle (SSMA) is an index that shows high sensitivity to a bridge local damage and only requires data obtained on from a vehicle passing the bridge. However, it is necessary to measure the vehicle's location on the bridge precisely as well as the vibrations. The accuracy of the recorded global positioning system (GPS) was lower than required. In this study, SSMA is calculated by shifting the position of the data window and by shifting the window, a SSMA curve is obtained. The SSMA curve shows high repeatability, which means that there is a possibility that the curve can detect damage. Keywords: drive-by bridge damage detection; vehicle response analysis; vehicle bridge interaction; singular value decomposition; SVD; spatial singular mode angle; SSMA Citation: International Journal of Lifecycle Performance Engineering, Vol. 3, No. 3/4 (2019) pp. 310 - 330 PubDate: 2019-11-22T23:20:50-05:00 DOI: 10.1504/IJLCPE.2019.103699 Issue No:Vol. 3, No. 3/4 (2019)

Authors:Kun Zhang, Zhouhong Zong, Yuchen Liao, Xingchen Fan, Jie Niu Pages: 331 - 359 Abstract: A comprehensive safety evaluation method which can dynamically reflect the damage changes in operation state is established based on the structural health monitoring (SHM) system of a composite girder cable-stayed bridge. The fuzziness and uncertainties during the evaluation process are considered and the random errors are reduced by using the proposed evaluation method. The normal values and safety limits of monitoring indexes of the Guanhe Bridge are proposed by using numerical simulation and monitoring data statistics of the baseline finite element model, and the index evaluation standard of the related code requirements. The results can be used to complement the lack of online monitoring indexes in the existing regulations, and solve the problem that lacking support for quantitative monitoring data in current bridge management system evaluation module, which can provide theoretical basis for the evaluation, management, maintenance and decision-making of bridge structures. Keywords: bridge safety assessment; cable-stayed bridge; comprehensive safety evaluation method; evaluation index system Citation: International Journal of Lifecycle Performance Engineering, Vol. 3, No. 3/4 (2019) pp. 331 - 359 PubDate: 2019-11-22T23:20:50-05:00 DOI: 10.1504/IJLCPE.2019.103701 Issue No:Vol. 3, No. 3/4 (2019)

Authors:Phung Tu, Vanissorn Vimonsatit Pages: 360 - 378 Abstract: Existing methods of determining silo pressures and flow rates use gravity as the only force acting on the bulk materials inside the silos. The effects of the vibrating silo supporting structure have been somewhat overlooked in existing silo flow models. As such, the structural integrity of the silo structure in some cases is compromised. Evidently, silo structures have the highest rate of failure. Fundamentals of applied physics and Newton's laws of motion suggest that the vibrating structure induces accelerations that can adversely affect the pressures, flow rates and structural integrity of the silo structure. In this paper, the formulae in AS3774 to calculate discharge pressures will be modified to include the structural responses, and the effects of the structural responses on the flow rates, and pressures will be presented. Such unique properties can be used to design better, monitor and maintain the silo structure. Keywords: silo vibration; silo quaking; fluctuating flow rates; fluctuating pressures Citation: International Journal of Lifecycle Performance Engineering, Vol. 3, No. 3/4 (2019) pp. 360 - 378 PubDate: 2019-11-22T23:20:50-05:00 DOI: 10.1504/IJLCPE.2019.103702 Issue No:Vol. 3, No. 3/4 (2019)